مهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Application of Multiple-Part Method length of Line to Improve the Simulation of Chlorine Decay in Big Isfahan Water Conveyance Lineکاربرد روش چند بخشی نمودن طول خط بهمنظور بهبود شبیهسازی زوال کلر در خطوط انتقال آب اصفهان بزرگ1119536010.22093/wwj.2019.176018.2842FAیاسمن فروزندهدانشجوی کارشناسی ارشد مهندسی و مدیریت منابع آب، گروه عمران، دانشکده مهندسی عمران و حملونقل، دانشگاه اصفهان، اصفهان، ایرانعلی دهنویاستادیار، گروه مهندسی عمران، دانشکده مهندسی عمران و حملونقل، دانشگاه اصفهان، اصفهان، ایراناحمد شانهساززادهاستادیار، گروه مهندسی عمران، دانشکده مهندسی عمران و حملونقل، دانشگاه اصفهان، اصفهان، ایرانJournal Article20190313Chlorine is used as the most common disinfectant to prevent microbial growth in water networks. The concentration of chlorine in distribution systems or water conveyance lines is reduced due to two different types of bulk and wall decay. In this study EPANET software is applied to numerically simulate chlorine decay in the Isfahan water supply line from the Baba Sheikhali water treatment plant to Naein. Two methods are applied for simulation and the results are compared to the measurement. In the first method, chlorine simulation was performed taking into account the whole Isfahan water conveyance line as one section (integrated) and determining a bulk decay and wall decay coefficient for the entire conveyance line. In the second method, the line was divided into two sections (bisection) and decay coefficients of chlorine for each section was separately considered. To determine the bulk reaction rate, the bottle tests were performed at 6o and 18o Celsius corresponding to winter and summer. The results indicated that separating the line to two and applying independent coefficients and decay parameters to each part improves the results and the RMSE values are reduced from 0.09 to 0.03 in summer and from 0.064 to 0.025 in winter. Therefore, dividing the line in two or more sections substantially improves the accuracy of the simulation of chlorine decay.<strong>کلر بهعنوان متداولترین ماده گندزدا برای جلوگیری از رشد میکربی در شبکههای آبرسانی استفاده میشود. غلظت کلر در سیستمهای توزیع و یا خطوط انتقال آب بهعلت دو نوع مختلف زوال تودهای و زوال جدار کاهش مییابد. در این پژوهش با استفاده از نرمافزار </strong><strong>EPANET</strong><strong>، زوال کلر در خط انتقال آب اصفهان از تصفیهخانه باباشیخعلی تا شهر نایین در فصول تابستان و زمستان با مدل سینتیکی مرتبه اول به دو روش تکبخشی و دو بخشی شبیهسازی و نتایج با یکدیگر مقایسه شد. در روش اول شبیهسازی کلر با در نظر گرفتن کل خط انتقال آب اصفهان بهعنوان یک بخش (تکبخشی) و تعیین یک ضریب زوال حجمی و یک ضریب زوال جدار برای کل خط انتقال انجام شد. در روش دوم خط انتقال به دو بخش تقسیم شد (دوبخشی) و ضرایب زوال کلر برای هر بخش جداگانه اختصاص داده شد. برای تعیین ضریب زوال تودهای کلر، آزمایشهای بطری در دماهای 6 و 18 درجه سلسیوس انجام شد. نتایج نشان داد با جداسازی خط انتقال به دو قسمت و استفاده از ضرایب و پارامترهای زوال متناسب با همان قسمت، مقدار خطای جذر میانگین مربعات برای غلظتهای کلر اندازهگیری شده و شبیهسازی شده در فصل تابستان از مقدار 09/0 به 03/0 و در فصل زمستان از 064/0 به 025/0 کاهش پیدا کرده است. بنابراین کاربرد روش چند بخشی بهصورت قابل ملاحظهای باعث بهبود نتایج شبیهسازی غلظت کلر در خطوط انتقال طولانی میشود.</strong>https://www.wwjournal.ir/article_95360_acefb7957614d79ea5da197ed9674440.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320The Optimized Implementation of the District Metered Areas in the Water Distribution Networks Using Graph Theoryاستقرار بهینه نواحی مجزا در شبکههای توزیع آب با استفاده از تئوری گراف12249208010.22093/wwj.2019.140550.2718FAمحمدرضا شکفتهدانشجوی کارشناسی ارشد، گروه مهندسی منابع آب، دانشکده مهندسی عمران، آب و محیط زیست، دانشگاه شهید بهشتی، تهران، ایرانمحمد رضا جلیلی قاضی زادهاستادیار، گروه مهندسی آب و فاضلاب، دانشکده مهندسی عمران، آب و محیط زیست،
دانشگاه شهید بهشتی، تهران، ایرانJournal Article20180717For better utilization of water distribution networks (WDNs), it is recommended that the existing networks be converted into Distinct Metered Areas (DMAs). Due to the complexity of the old networks, the conversion of these networks into DMA is a costly and sensitive issue. In this paper, a model has been developed to optimize implementation of the old networks into DMA by using the graph theory and water distribution system modeling software (EPANET), while the minimum required standard pressure is met and the number of linked pipes between the proposed areas is minimum. The minimum number of linked pipes will minimize the cost of the needed flowmeters. The developed model has been successfully applied for Poulakis WDN with 30 nodes and 50 pipes in different statuses and for the actual Bushehr WDN with about 3740 nodes and 3980 pipes. The output result shows that the developed model, in a satisfactory way, converts water distribution networks into DMAs with respect to the hydraulic constrainsts.<strong>برای بهرهبرداری بهتر از شبکههای توزیع آب توصیه میشود که شبکههای موجود به نواحی مجزا تبدیل شود. بهدلیل پیچیدگی شبکههای قدیمی، تبدیل این شبکهها به نواحی مجزا، پرهزینه و حساس است. در پژوهش حاضر مدلی ارائه شد که با استفاده از تئوری گراف و نرمافزار شبیهسازی هیدرولیکی </strong><strong>EPANET</strong><strong>، تبدیل شبکههای قدیمی به نواحی مجزا را بهصورت بهینه انجام میدهد، بهصورتی که ضمن رعایت حداقل فشار مورد نیاز گرهها، تعداد لولههای رابط بین نواحی مجزای پیشنهادی حداقل باشد. حداقل بودن تعداد لولههای رابط، باعث حداقل شدن هزینه برای دبیسنجهای مورد نیاز میشود. مدل ارائه شده برای تعیین نواحی مجزا برای شبکه توزیع آب پولاکیس با 50 لوله و 30 گره در حالتهای مختلف هیدرولیکی و همچنین برای شبکه واقعی آب شهر بوشهر با حدود 3740 گره و 3980 لوله بهکار گرفته شد. نتایج خروجی نشان داد که مدل ارائه شده، توانایی طراحی شبکههای آب موجود به نواحی مجزا را با رعایت قیدهای هیدرولیکی بهصورت بهینه دارد.</strong>https://www.wwjournal.ir/article_92080_5da09991115de748c8e6136d7d8f82ac.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Estimate Proportional Contributions of Multiple Nitrate Sources in Groundwater of Varamin Plain Using a Bayesian Isotope Mixing Modelتخمین سهم نسبی منابع چندگانه نیترات در آب زیرزمینی دشت ورامین با استفاده از مدل اختلاط ایزوتوپی بیزی25389661810.22093/wwj.2019.170201.2821FAزهره نجاتی جهرمیدانشجوی دکتری هیدروژئولوژی گروه زمین شناسی معدنی و آب، دانشکده علوم زمین، دانشگاه شهید بهشتی تهران، ایرانحمیدرضا ناصریاستاد، گروه زمینشناسی معدنی و آب، دانشکده علوم زمین، دانشگاه شهید بهشتی، تهران، ایرانمحمد نخعیاستاد، گروه زمینشناسی کاربردی، دانشکده علوم زمین، دانشگاه خوارزمی، کرج، ایرانفرشاد علیجانیاستادیار، گروه زمینشناسی معدنی و آب، دانشکده علوم زمین، دانشگاه شهید بهشتی، تهران، ایران0000-0002-0124-1215Journal Article20190130Nitrate (NO<sub>3</sub><sup>−</sup>) pollution of surface and ground water is a major problem in water quality on the planet. The scientific method of the relations between δ15N-NO<sub>3</sub><sup>−</sup> and δ18O-NO<sub>3</sub><sup>−</sup> to identified the dominant sources of nitrate in groundwater, despite the overlap of nitrate isotopic ranges and the occurrence of nitrate isotopic fractionation, have been used in numerous studies. NH<sub>4</sub><sup>+</sup> fertilizer, treated wastewater, sewage and manure, Shour River, NO<sub>3</sub> in precipitation and soil organic N, are potential sources of nitrate pollution in the study area. To identify different nitrate sources and to estimate their proportional contribution in the groundwater of the Varamin aquifer, a dual isotope (δ<sup>15</sup>N-NO<sub>3</sub><sup>−</sup> and δ<sup>18</sup>O-NO<sub>3</sub><sup>−</sup>) method and a Bayesian isotope mixing model for 38 samples in November 2016 have been applied. Based on hierarchical cluster analysis, 38 groundwater samples are classified into three clusters (groups one to three) in terms of hydrochemical properties., the mean values of δ<sup>15</sup>N–NO<sub>3</sub><sup>−</sup> in groups 1, 2 and 3 are +7.0± 2.1‰, +10.2 ±1.1‰ and +16.1±2.1‰, respectively. The mean of δ<sup>18</sup>O–NO<sub>3</sub><sup>−</sup> values of the groundwater in groups 1, 2 and 3 are +2.3± 1.9‰, +0.6 ± 0.8‰ and +6.2 ± 1.4‰ , respectively. SIAR model results indicate that the highest contribution in the nitrate pollution of the Varamin aquifer are related to“NH<sub>4</sub><sup>+</sup> fertilizer” and “manure and sewage” while “soil N” and “NO<sub>3</sub><sup>−</sup> in precipitation” have the lowest influence.<strong>آلودگی نیترات آبهای سطحی و زیرزمینی مشکل مهم کیفیت آب در کره زمین است. در پژوهشهای متعدد از روش علمی تعیین روابط </strong><strong>δ15N- </strong><strong> و </strong><strong>δ18O- </strong><strong> برای مشخص نمودن منابع غالب نیترات در آبهای زیرزمینی، با وجود همپوشانی دامنههای ایزوتوپ نیترات و وقوع تفریق ایزوتوپی نیترات، استفاده میشود. منابع پتانسیل نیترات در منطقه مورد مطالعه شامل کودهای شیمیایی آمونیومدار، پساب تصفیهخانه فاضلاب جنوب تهران، فاضلابهای انسانی و حیوانی، رودخانه شور، بارندگی و نیتروژن آلی خاک است. برای شناسایی منابع مختلف نیترات و تخمین سهم نسبی آنها در آب زیرزمینی آبخوان ورامین، از ایزوتوپهای دوگانه نیترات (</strong><strong>δ15N- </strong><strong> و </strong><strong>δ18O- </strong><strong>) و مدل اختلاط ایزوتوپی بیزی برای 38 نمونه در آبان 1396 استفاده شد. بر اساس آنالیز خوشهای سلسله مراتبی، 38 نمونه آب زیرزمینی از لحاظ خصوصیات هیدروشیمیایی به سه خوشه (گروههای یک تا سه) تقسیمبندی شدند. میانگین مقدار </strong><strong>δ15N- </strong><strong> برای گروههای 1، 2 و 3 بهترتیب </strong>‰<strong>1/2 ±7+، </strong>‰<strong>1/1 ±2/10+ و </strong>‰<strong>1/2 ± 1/16+ و میانگین </strong><strong>δ18O- </strong><strong>، بهترتیب </strong>‰<strong>9/1 ±3/2+ ، </strong>‰<strong>8/0 ±6/0+، </strong>‰<strong>4/1 ±2/6+ بود. مدل </strong><strong>SIAR</strong><strong> نشان داد که کودهای آمونیومدار و فاضلاب، بیشترین سهم نیتروژن آلی خاک و بارندگی کمترین سهم را در آلودگی نیترات آبخوان ورامین دارند.</strong>https://www.wwjournal.ir/article_96618_51915791c962c2ecbd661defe703db0f.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Photocatalytic Removal of Ethylene Dichloride Using PAni-TiO2 Nanocomposites Supported on Glass Beads: Process Optimization by RSM-CCD Approachحذف فتوکاتالیستی اتیلن دیکلراید توسط نانوکامپوزیت پلی آنیلین-دی اکسید تیتانیم تثبیت شده بر سطح گلولههای شیشهای: بهینهسازی به روش سطح پاسخ-طراحی مرکب مرکزی39529208410.22093/wwj.2019.166423.2805FAمهدی محسن زادهدانشجوی دکترای مهندسی عمران- محیط زیست، دانشکده مهندسی عمران، دانشگاه صنعتی خواجه نصیرالدین طوسی، تهران، ایرانسید احمد میرباقریاستاد، گروه مهندسی محیط زیست، دانشکده مهندسی عمران، دانشگاه صنعتی خواجه نصیرالدین طوسی، تهران، ایرانJournal Article20190108Ethylene dichloride is one of the most important chlorinated hydrocarbons in the petrochemical industry, which is mainly used to produce vinyl chloride monomer, the main precurser of PVC production. Iran is one of the largest PVC producers in the world. During the production of 1000 kg of ethylene dichloride, about 0.4 m<sup>3</sup> wastewater is produced containing 50-200 mg / L of ethylene dichloride. In this study, heterogeneous photocatalysis was used for degradation of this chlorinated hydrocarbon. PAni-TiO<sub>2</sub> nanocomposite was immobilized on glass beads by a modified dip coating and heat attachment method. The morphology characteristics were confirmed by scanning electron microscope, energy dispersive X-ray spectroscopy and ultraviolet–visible spectroscopy. A pilot scale packed bed recirculating batch photocatalytic reactor was used for conducting photocatalytic experiments. response surface methodology based on central composite design was used to evaluate and optimize the effect of ethylene dichloride concentration, residence time, pH and coating mass as independent variables on the photocatalytic degradation of ethylene dichloride as the response function. Based on the results, actual and RSM predicted results were well fitted with R<sup>2</sup> of 0.9870, adjusted R<sup>2</sup> of 0.9718 and predicted R<sup>2</sup> of 0.9422. Optimum conditions were the ethylene dichloride concentration of 250 mg/L, reaction time of 240 min, pH of 5 and immobilized mass of 0.5 mg/cm<sup>2</sup>, which resulted in 88.84% photocatalytic degradation. Kinetic of the photocatalytic degradation at optimal condition followed the Langmuir-Hinshelwood first order reaction with k=0.0095 min<sup>-1</sup> with R<sup>2</sup>=0.9455. Complete photocatalytic degradation of ethylene dichloride was achieved after 360 min. Based on the results, it may be argued that the designed and constructed photocatalytic reactor has the potential for industrialization.<strong>اتیلن دیکلراید یکی از مهمترین هیدروکربنهای کلرینه در پساب صنایع پتروشیمی است که عمدتاً برای تولید مونومر وینیل کلراید که پیش ماده اصلی تولید پیویسی است، استفاده میشود. ایران یکی از بزرگترین تولیدکنندگان پیویسی در جهان است. در فرایند تولید ۱۰۰۰ کیلوگرم اتیلن دیکلراید، در حدود 4/0 مترمکعب پساب تولید میشود که حاوی ۵۰ تا ۲۰۰ میلیگرم در لیتر اتیلن دیکلراید است. در این پژوهش، روش تجزیه فتوکاتالیستی برای حذف این هیدروکربن کلرینه مورد استفاده قرار گرفت. نانوکامپوزیت </strong><strong>PAni-TiO<sub>2</sub></strong><strong> به روش لایهنشانی غوطهوری بر سطح گلولههای شیشهای تثبیت شد. خصوصیات مورفولوژی نانوکامپوزیت </strong><strong>PAni-TiO<sub>2</sub></strong><strong> با استفاده از تحلیلهای میکروسکوپ الکترونی روبشی، طیف سنجی پراش انرژی پرتو ایکس و طیف سنجی مرئی- فرابنفش مورد تأیید قرار گرفت. یک راکتور فتوکاتالیستی بستر ثابت در مقیاس نیمه صنعتی برای آزمایشهای فوتوکاتالیستی مورد استفاده قرار گرفت. روش سطح پاسخ بر اساس طراحی مرکب مرکزی برای ارزیابی و بهینهسازی پارامترهای غلظت اولیه اتیلن دیکلراید، زمان ماند، </strong><strong>pH</strong><strong> و ضخامت پوشش بهعنوان پارامترهای مستقل و حذف فتوکاتالیستی اتیلن دیکلراید بهعنوان پاسخ، در نظر گرفته شد. بر اساس نتایج بهدست آمده، دادههای واقعی و مقادیر پیشبینی شده توسط روش سطح پاسخ با ضریب رگرسیون 9870/0 و ضریب رگرسیون اصلاح شده 9718/0 و ضریب رگرسیون پیشبینی شده 9422/0 همبستگی داشتند. مطابق نتایج، در شرایط بهینه غلظت اولیه اتیلن دیکلراید 250 میلیگرم در لیتر, زمان ماند 240 دقیقه, </strong><strong>pH</strong><strong> برابر 5 و ضخامت پوشش 5/0 میلیگرم بر سانتیمتر مربع، درصد تجزیه فتوکاتالیستی اتیلن دیکلراید 84/88 بود. سینتیک تجزیه فتوکاتالیستی در شرایط بهینه از مدل مرتبه اول لانگمیر-هینشلوود با ثابت سرعت مرتبه اول (</strong><strong>K</strong><strong>) برابر 0095/0 و ضریب رگرسیون برابر 9455/0 پیروی میکرد. حذف کامل فتوکاتالیستی اتیلن دیکلراید پس از 360 دقیقه بهدست آمد. از نتایج بهدست آمده در این پژوهش میتوان نتیجه گرفت راکتور طراحی و ساخته شده، احتمالاً قابلیت صنعتی شدن را دارد.</strong>https://www.wwjournal.ir/article_92084_e8510a97dbf681ce84deb293621f00e3.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Investigation of Copper Ion Adsorption by Alpha, Beta and Gamma Cyclodextrin by Density Function Methodبررسی جذب یون مس با آلفا، بتا و گاما سیکلودکسترین با استفاده از روش تابع چگالی53609277910.22093/wwj.2019.115799.2614FAحسین نورمحمدیدانشجوی دکترا، گروه معدن (فراوری مواد معدنی)، دانشکده فنی و مهندسی، دانشگاه صنعتی تبریز سهند، تبریز، ایرانلیلی حیدرپور صارمیدانشجوی دکترا، گروه شیمی فیزیک، دانشکده علوم پایه، دانشگاه سیستان و بلوچستان، زاهدان، ایرانوالح آقازادهدانشیار، گروه معدن، دانشکده فنی و مهندسی، دانشگاه صنعتی تبریز سهند، تبریز، ایرانJournal Article20180630Cyclodextrins are categorized into three groups of alpha, beta, and gamma, according to the number of their own glucose units of 6, 7 and 8 units. These ring compounds have two surfaces of hydrophilic and hydrophobic to trap compounds with different polarities. twofold behavior of cyclodextrins has attracted the attention of the various industries, including pharmaceuticals, medicine and cosmetics. Metal cations are one of the sources of pollution of industrial and mining wastewater. In this work, the theory of the interaction of Cu<sup>1+</sup> metal cation with alpha, beta, and gamma cyclodextrin has been studied. The structure and stability energy of these compounds are investigated using the Density functional theory and the B3LYP method with a base set of 6-31g (d, p) in the gas phase and solution. Using the NBO calculations, the active site of these compounds was determined for interaction with metal cation. The calculations showed that the distribution of charge on the glucopyranose oxygen atoms as the constructors of each constructor is approximately the same. Also, the corresponding complexes were optimized using the computational level and the Chelating ability of each of these rings oligosaccharides comparison has been made. Using the NBO calculations, the active site of these compounds was determined for interaction with metal cation. The calculations showed that the distribution of charge on the glucopyranose oxygen atoms as the constructors of each constructor is approximately the same. Also, the corresponding complexes were optimized using the computational level and the Chelating ability of each of these rings oligosaccharides comparison has been made.<strong>سیکلودکسترینها با توجه به تعداد واحدهای گلوکزی تشکیل دهنده خود، 6، 7 و 8 واحد، بهترتیب به سه دسته آلفا، بتا و گاما سیکلودکسترین طبقهبندی میشوند. این ترکیبات حلقوی دارای دو سطح آبدوست و آبگریز برای به دام انداختن ترکیبات با قطبیتهای مختلف هستند. رفتار دوگانه سیکلودکسترینها سبب کاربرد آنها در زمینههای مختلف از جمله داروسازی، پزشکی، زیستمحیطی و آرایشی شده است. کاتیونهای فلزی یکی از منابع آلودگی پسابهای معدنی و صنعتی هستند، که فرایند حذف آنها با سیکلودکسترین موضوع پژوهش حاضر است. در این پژوهش، آنالیز تئوری برهمکنش کاتیون فلزی </strong><strong>Cu<sup>1+</sup></strong><strong>با آلفا، بتا و گاما سیکلودکسترین مورد مطالعه قرار گرفت. ساختار و انرژیهای پایداری این ترکیبات با استفاده از نظریه دانسیته الکترونی و روش </strong><strong>B3LYP</strong><strong> در فاز گازی و محلول بررسی شد. با استفاده از محاسبات </strong><strong>NBO</strong><strong>، جایگاههای فعال این ترکیبات برای برهمکنش با کاتیون فلزی مشخص شدند. محاسبات نشان داد توزیع بار الکتریکی بر روی اتمهای اکسیژن گلوکوپیرانوز بهعنوان واحدهای سازنده هر ترکیب تقریباً یکسان است. همچنین کمپلکسهای مربوطه با استفاده از سطح محاسباتی مذکور بهینهسازی شد و قدرت کیلیت شدن هرکدام از این الیگوساکاریدهای حلقهای مورد مقایسه قرار گرفت. دادهها نشان دادند که آلفا و بتا سیکلودکسترین بهترتیب تمایل بیشتری برای برهمکنش با کاتیون </strong><strong>Cu<sup>1+</sup></strong><strong>در فاز گازی و آبی دارند و بنابراین نامزدهای احتمالی برای زدودن این یون از پسابهای صنعتی و یا معدنی بهشمار میروند.</strong>https://www.wwjournal.ir/article_92779_73d43d1943267182de155a120498f46e.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Investigating the Efficiency of Phosphate Removal from Wastewater from Sugar Cultivation Industry Using Baffled Subsurface-Flow Constructed Wetlandبررسی کارایی حذف فسفات از زهاب صنایع کشت و صنعت نیشکر با استفاده از سیستم تالاب بافلدار ساختگی با جریان زیر سطحی61759277810.22093/wwj.2019.164326.2798FAصادق قاسمیدانشجوی دکترا، گروه مهندسی عمران- مهندسی و مدیریت منابع آب، واحد شوشتر،
دانشگاه آزاد اسلامی، شوشتر، ایراناحسان دریکونداستادیار گروه مهندسی عمران - مهندسی و مدیریت منابع آب، واحد شوشتر،
دانشگاه آزاد اسلامی، شوشتر، ایرانصائب خوشنوازاستادیار گروه مهندسی عمران - مهندسی و مدیریت منابع آب، واحد شوشتر، دانشگاه آزاد اسلامی، شوشتر، ایرانسعید برومند نسباستاد دانشکده مهندسی علوم آب، دانشگاه شهید چمران اهوازمحسن سلیمانی بابرصاداستادیار گروه مهندسی عمران - مهندسی و مدیریت منابع آب، واحد شوشتر، دانشگاه آزاد اسلامی، شوشتر، ایرانJournal Article20181225Phosphorus is recognized as a nutrient in aquatic environments, but increasing its concentration in water resources causes the occurrence of eutrophication in water and, as a result, causes the death of aquatic organisms. Therefore, removal of phosphate from water is very important. In this research, in order to remove phosphate from water resources, the baffled subsurface-flow constructed wetland was used. In order to increase the efficiency of the wetland system, experiments were designed in 3 different phases. In the first phase, in the form of batch experiments, the composite performance of cheap materials such as zeolite, bentonite and pumice aggregates (The stabilization of nanoparticles of zeolite\bentonite on the surface of Pumice aggregates) to absorb phosphate and select the preferred candidate for placement in the wetland was investigated. In the second phase, in the form of pot experimentation, the performance of native plants of khuzestan province such as salicornia, Typha, and Juncus, In order to uptake phosphate and select the best candidate for cultivation in the bed of the wetland was investigated. Finally, in the third phase, with the placement of the selected bedding and plant (selected from previous experiments) in the wetland system, experiments were carried out to study the effect of parameters such as the percentage of optimum mix of Selected bed with gravel, hydraulic residence time and temperature changes on the phosphate removal efficiency. The results showed that among absorbent materials and candidate plants for placement and cultivation in the wetland, the maximum capacity to absorb and accumulate phosphate by Pumice aggregate coated by zeolite nanoparticles (1.08 mg/g) and salicornia (9.68 mg/g of plant dry weight) was observed. In this experiment, The use of a combination of 10% of the selected bed with 90% of the gravel was obtained as the best and most economical option for removal of phosphate. Also, the efficiency of removal of phosphate in the 1-day hydraulic residence time was achieved at the highest intensity (99.60%) and was selected as the optimum time to remove phosphate. Finally, the results of the effect of temperature changes on the efficiency of the wetland system showed that the removal efficiency from March 2018 (20 °C) to July 2018 (40 °C) increased to about 1 percent, which indicates the effect of temperature changes on the performance of the wetland system. According to the results, in the case of adequate land availability, the use of subsurface-flow constructed wetland systems to wastewater treatment of agricultural and industrial units is very convenient and cost-effective.<strong>فسفر در محیطهای آبی بهعنوان یک ماده مغذی ضروری شناخته میشود اما افزایش غلظت آن در منابع آبی باعث بروز پدیده یوتریفیکاسیون در آب و در نتیجه مرگ آبزیان میشود. بنابراین حذف فسفات از آب بسیار مهم است. در این پژوهش بهمنظور حذف فسفات از منابع آب از سیستم تالاب بافلدار ساختگی با جریان زیر سطحی استفاده شد. در همین راستا برای افزایش کارایی سیستم تالاب ساخته شده در حذف بهینه فسفات، آزمایشهایی در 3 فاز مختلف طراحی شد. در فاز اول در قالب آزمایشهای ناپیوسته، عملکرد کامپوزیت مواد ارزان قیمتی همچون زئولیت، بنتونیت و سنگدانه پامیس بهصورت تثبیت نانوذرات زئولیت/ بنتونیت بر روی سطح سنگدانههای پامیس بهمنظور جذب فسفات و انتخاب کاندید برتر بهمنظور قرارگیری در بستر تالاب مورد بررسی قرار گرفت. در فاز دوم در قالب آزمایشهای گلدانی، عملکرد گیاهان بومی استان خوزستان همچون سالیکورنیا، لویی و سازو بهمنظور جذب فسفات و انتخاب کاندید برتر جهت کشت در بستر تالاب مورد بررسی قرار گرفت و در نهایت در فاز سوم با قرارگیری بستر و گیاه منتخب در سیستم تالاب ساخته شده، آزمایشهایی بهمنظور بررسی اثر پارامترهایی همچون درصد ترکیب بهینه بستر منتخب با شن، زمان ماند هیدرولیکی و تغییرات دمایی بر راندمان حذف فسفات انجام و تحلیل شد. از بین مواد جاذب و گیاهان کاندید شده برای قرارگیری و کشت در بستر تالاب، بیشترین ظرفیت جذب و انباشت فسفات در سنگدانههای پامیس پوشش داده شده نانوذرات زئولیت 02/1 میلیگرم بر گرم و گیاه سالیکورنیا (68/9 میلی گرم در گرم وزن خشک گیاه) مشاهده شد. در این آزمایش استفاده از ترکیب 10 درصد بستر منتخب با 90 درصد شن بهعنوان بهترین و اقتصادیترین گزینه در حذف فسفات بهدست آمد. همچنین راندمان حذف فسفات در زمان ماند هیدرولیکی 1 روزه در بیشترین شدت، 60/99 درصد بهدست آمد و بهعنوان زمان ماند بهینه مناسب برای حذف فسفات انتخاب شد. در نهایت بررسی نتایج اثر تغییرات دمایی در کارایی سیستم تالاب نشان داد که راندمان حذف از اسفندماه 1396 (دمای 20 درجه سلسیوس) تا تیرماه 1397 (دمای 40 درجه سلسیوس) به میزان 1 درصد افزایش یافت که نشاندهنده تأثیر تغییرات دمایی بر کارایی سیستم تالاب است. با توجه به نتایج بهدست آمده در صورت در دسترس بودن زمین کافی، استفاده از سیستمهای تالاب مصنوعی با جریان زیر سطحی برای تصفیه پساب واحدهای کشاورزی و صنعتی بسیار مناسب و مقرون به صرفه است.</strong>https://www.wwjournal.ir/article_92778_347c72450446062417f6f0652dc7e0b4.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Optimization of Wastewater Refinery in Shokoohiyeh Industrial City of Qom Before Entering RO System Using Chlorophyll, Alum and PAC Coagulatorsبهینهسازی پساب تصفیهخانه فاضلاب لجن فعال شهرک صنعتی شکوهیه قم قبل از ورود به سیستم RO با استفاده از منعقدکنندههای کلرورفریک، آلوم و PAC76859559010.22093/wwj.2019.149946.2753FAحمزه قاسم آهنگریکارشناس ارشد مهندسی آلودگیهای محیط زیست، دانشکده منابع طبیعی، دانشگاه آزاد واحد اصفهان (خوراسگان)، اصفهان، ایرانحسین پورمقدساستاد، دانشگاه آزاد اسلامی، گروه کشاورزی- محیط زیست، دانشکده کشاورزی، واحد اصفهان (خوراسگان)، اصفهان، ایرانمحمد فهیمی نیادکترای بهداشت محیط، مرکز تحقیقات آلایندههای محیطی، دانشگاه علوم پزشکی قم، قم، ایرانJournal Article20180927The effluent from the active sludge treatment plant of Qom Shokoohiyeh industrial flows into surface water and reuse of water in industrial process is necessary. The aim of this study was to investigate the efficiency of aluminum sulfate, chlorofluorocarbons and poly aluminum chloride in removing turbidity and other parameters in industrial wastewater before entering RO in Shokoohiyeh Qom industrial refinery. This study was applied in a laboratory scale using a jar-test and experiments based on varying concentrations of coagulants (200, 400, 700, 800, 1000, 1200 mg/L) and pH=2.4.6.7.8.10 has been done. Steady mixing, slow mixing and stagnation have been performed and factors such as turbidity, pH, COD, BOD<sub>5</sub>, EC, SVI and TSS have been investigated. Coagulants are effective in removing turbidity. The highest removal rate was for polyvinyl chloride (95%) and the least amount of turbidity removal was in chlorofacry (50%). The highest and lowest levels of pH were detected at pH=2 (72%) and pH=8 (10%), respectively. The lowest BOD<sub>5</sub> removal efficiency in poly aluminum chloride was 88% at pH=4 and the highest removal rate of BOD<sub>5</sub> was found in chloroformate coagulant with pH=4 (96%). The highest COD reduction was observed in poly aluminum chloride at pH=9 (89%) and the lowest COD reduction was observed at a concentration of 800 mg/L alum with 34%. The highest reduction in electric conductivity in poly aluminum chloride with 87% and the lowest amount of electrical conductivity reduction occurred at a concentration of 500 mg per liter of alum with 12%. The highest total removal of suspended solids in chlorofacrylic coagulant was 88% and the lowest amount was removed in chloroform with up to 18%. The maximum amount of sludge deposited at pH=9 (240 mg/L) in aluminum chloride and the lowest amount of sludge deposited at pH=2 (5 mg/L). The use of coagulant materials can increase the purification efficiency, eliminate opacity and return water to the cycle. PAC and Alum coagulant have high efficiency in removing turbidity and other wastewater treatment parameters that can be used to treat wastewater for RO systems.<strong>پساب خروجی از تصفیهخانه لجن فعال شهرک صنعتی شکوهیه قم به آبهای سطحی جریان دارد و استفاده مجدد از آب در فرایند صنعتی امری ضروری است. این پژوهش با هدف بررسی کارایی سولفات آلومینیوم، کلرورفریک و پلیآلومینیوم کلراید در حذف کدورت و بقیه پارامترها در پساب صنعتی، قبل از ورود به سیستم</strong><strong>RO</strong><strong> در تصفیهخانه صنعتی شکوهیه قم انجام شد. آزمایشها بر اساس غلظتهای متغیر منعقدکنندهها (200، 400، 700، 800، 1000، 1200 میلیگرم در لیتر) و </strong><strong>pH</strong><strong> (2، 4، 6، 7، 8 و 10) انجام شد. مراحل اختلاط سریع، اختلاط آرام و سکون انجام شد و عواملی از قبیل کدورت، </strong><strong>pH</strong><strong>، </strong><strong>COD</strong><strong>، </strong><strong>BOD<sub>5</sub></strong><strong>، </strong><strong>EC</strong><strong>، </strong><strong>SVI</strong><strong> و </strong><strong>TSS</strong><strong> مورد بررسی قرار گرفت. کارایی منعقدکنندهها در حذف کدورت، متفاوت بود. بالاترین میزان حذف کدورت با پلیآلومینیوم کلراید (95 درصد) و کمترین مقدار حذف کدورت با کلرورفریک (50 درصد) مشاهده شد. بیشترین و کمترین میزان کاهش به ترتیب در </strong><strong>pH</strong><strong> برابر 2 با 72 درصد و در </strong><strong>pH</strong><strong> برابر 8 با 10 درصد مشاهده شد. کمترین راندمان حذف </strong><strong>BOD<sub>5</sub></strong><strong> در پلی آلومینیوم کلراید برابر 88 درصد در </strong><strong>pH</strong><strong> برابر 4 و بالاترین میزان حذف </strong><strong>BOD<sub>5</sub></strong><strong> در منعقدکننده کلرورفریک برابر 96 درصد و در </strong><strong>pH</strong><strong> برابر 4 رخ داد.</strong><strong> بالاترین میزان کاهش </strong><strong>COD</strong><strong> در پلیآلومینیوم کلراید در </strong><strong>pH</strong><strong> برابر 9، 89 درصد و کمترین مقدار کاهش </strong><strong>COD</strong><strong> در غلظت 800 میلیگرم در لیتر آلوم برابر 34 درصد بود. بیشترین کاهش هدایت الکتریکی در پلیآلومینیوم کلراید با 87 درصد و کمترین مقدار کاهش هدایت الکتریکی در غلظت 500 میلیگرم در لیتر آلوم با 12 درصد رخ داد. بیشترین مقدار حذف کل جامدات معلق در منعقدکننده کلرورفریک 88 درصد و کمترین مقدار حذف 18 درصد بود. بیشترین حجم لجن تهنشین شده در </strong><strong>pH</strong><strong> برابر 9 معادل 240 میلیگرم در لیتر در پلیآلومینیوم کلراید و کمترین مقدار لجن تهنشین شده در </strong><strong>pH</strong><strong> برابر 2 معادل 5 میلیگرم در لیتر بود. استفاده از مواد منعقدکننده میتواند موجب افزایش راندمان تصفیه و حذف کدورت و بازگشت آب به چرخه شود. منعقدکننده </strong><strong>PAC</strong><strong> و آلوم کارایی بالایی در حذف کدورت و بقیه پارامترهای پساب تصفیهخانه دارند و میتوانند برای تصفیه پساب جهت تغذیه در سیستم </strong><strong>RO</strong><strong> مورد استفاده قرار گیرند.</strong>https://www.wwjournal.ir/article_95590_3acc528a5e55f5cba0d06d1e6e980e6c.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Number of Blockage Prediction for Sanitary Sewer Networks (Case Study: Isfahan Region 2)پیشبینی تعداد گرفتگی در شبکه فاضلاب شهری (مطالعه موردی: منطقه دو اصفهان)86989276010.22093/wwj.2019.143553.2731FAپگاه حسینقلیدانشجوی کارشناسی ارشد مهندسی و مدیریت منابع آب، گروه عمران، دانشکده مهندسی عمران و حمل و نقل، دانشگاه اصفهان، اصفهان، ایرانرامتین معینیاستادیار، گروه عمران، دانشکده مهندسی عمران و حمل و نقل، دانشگاه اصفهان، اصفهان، ایرانمحمد رضا زارعاستادیار، گروه عمران، دانشکده مهندسی عمران و حمل و نقل، دانشگاه اصفهان، اصفهان، ایرانJournal Article20180807Wastewater network is an inseparable part of urban life. Due to importance of this network as one of the urban infrastructure, the failure of this system will lead to stopping service, causing many social, economic and environmental consequences. Hence, assessing the wastewater networks condition and its failure is an important approach for managing it. Generally, failure of system means any condition which is lead to stopping service. In general, artificial intelligence methods are used as a low-cost method to predict failure. In this research, genetic programming (GP) is used to predict the number of blockage (hydraulic failure) in the wastewater network and its results are compared with the results of the artificial neural network (ANN). As a case study, here, a part of Isfahan wastewater network is investigated. The parameters such as age, pipe length, slope and depth as input data and the number of blockage are considered as the output data of the model. In this research, the number of blockage data in the wastewater network at 1394 and 1395 are used, in which the 70% of the data is used for training and 30% for the test. These data are classified in three way leading to three model. In the first model, data are classified based on the slope and in two other models the data are classified according to the cover depth. The results show that all models predicts the number of blockage with good accuracy. In addition the accuracy of the result of GP model is better than the ANN model. For example, for GP model, the values of R<sup>2</sup> and RMSE for the second model at the training stage are 0.97 and 0.8 and at the test stage are equal to 0.94 and 0.69, respectively. However these values for ANN model are 0.96 and 0.95 at the training stage and 0.87 and 0.96 at the test stage respectively. These results show the superiority of the GP model in comparison with ANN model in which the results of second proposed model are better. The results of these proposed model can be used for preventive maintenance, prioritization of sewage network repairs and inspections, and finally to prevents the occurrence of suddenly accidents.<strong>امروزه شبکه فاضلاب بخش جداییناپذیر زندگی شهری محسوب میشود. با توجه به اهمیت این شبکه بهعنوان یکی از زیرساختهای شهری، وقوع شکست در این سیستم علاوه بر توقف سرویسدهی، منجر به ایجاد پیامدهای اجتماعی، اقتصادی و محیطزیستی زیادی میشود. از اینرو ارزیابی وضعیت شبکههای فاضلاب و شکستهایی که در شبکه اتفاق میافتد یک رویکرد مهم در مدیریت آن است. در حالت کلی منظور از شکست، کلیه حالاتی است که عملکرد سیستم با مشکل مواجه میشود. بهطور کلی روشهای هوش مصنوعی بهعنوان روشی کمهزینه بهمنظور پیشبینی شکست مورد استفاده قرار میگیرند. در این پژوهش از برنامهریزی ژنتیک بهمنظور پیشبینی تعداد گرفتگی (شکست هیدرولیکی) در شبکه فاضلاب، استفاده و نتایج آن با نتایج حاصل از مدل شبکه عصبی مقایسه شد. بهاین منظور قسمتی از شبکه فاضلاب شهر اصفهان بهعنوان مطالعه موردی بررسی شد. با توجه به پارامترهای تأثیرگذار بر شکست هیدرولیکی، پارامترهایی نظیر سن، طول، شیب و عمق دفن لولهها بهعنوان ورودی و تعداد گرفتگی بهعنوان خروجی مدل در نظر گرفته شد. در این پژوهش از اطلاعات مربوط به گرفتگی در شبکه فاضلاب مربوط به سالهای 1394 و 1395 استفاده شد که 70 درصد دادهها برای آموزش و 30 درصد برای آزمایش بهکار رفت. اطلاعات به سه شکل دستهبندی شد و سه مدل مختلف ارائه شد. در مدل اول اطلاعات بر اساس شیب و در دو مدل دیگر اطلاعات بر اساس عمق دفن، دستهبندی شدند و نتایج تحلیل شد. بررسی نتایج نشان داد که هر سه مدل دارای نتایج قابل قبولی هستند. همچنین مقایسه نتایج دو مدل نشان داد که دقت روش برنامهریزی ژنتیک نسبت به شبکه عصبی بهتر است. بهطور نمونه، در برنامهریزی ژنتیک مقدار </strong><strong>R<sup>2</sup></strong><strong> و </strong><strong>RMSE</strong><strong> برای مدل دوم در مرحله آموزش، 97/0 و 8/0 و در مرحله آزمایش بهترتیب برابر 94/0 و 69/0 بود که این مقادیر در شبکه عصبی در مرحله آموزش، 96/0 و 95/0 و در مرحله آزمایش بهترتیب برابر 87/0 و 96/0 بود. با بررسی نتایج بهدست آمده، برتری روش برنامهریزی ژنتیک نسبت به شبکه عصبی مشهود است. همچنین مدل دوم نتایج بهتری داشت. نتایج حاصل از این مدلها را میتوان در زمینه تعمیرات پیشگیرانه، اولویتبندی تعمیرات و بازرسیهای شبکه فاضلاب بهکار برد و در نتیجه از وقوع حوادث ناگهانی در شبکه جلوگیری نمود.</strong>https://www.wwjournal.ir/article_92760_0e7d0f842087c5c08f07c41d4a335b1a.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Investigating the Potential of Swimming Pools Sullage Reuse for Landscape Irrigation, Case Study: Tehran cityبررسی پتانسیل استفاده مجدد از پساب استخرهای شنا برای آبیاری فضای سبز، مطالعه موردی شهر تهران991109593110.22093/wwj.2019.118532.2624FAمریم ایزدپناهدانش آموخته کارشناسی ارشد مهندسی شیمی، کرسی یونسکو در بازیافت آب،
دانشکده مهندسی شیمی، پردیس دانشکدههای فنی، دانشگاه تهران، تهران، ایرانمحمد حسین صرافزادهدانشیار، رئیس کرسی یونسکو در بازیافت آب، دانشکده مهندسی شیمی، پردیس دانشکدههای فنی، دانشگاه تهران، تهران، ایرانJournal Article20190316In recent years, excessive usage of surface and underground water resources has exerted great stress on Iran's water resources. A survey of water use trends in the past years and forecasts of water needs in the coming years, makes undesirable perspective for the imbalance between water demand and resources in the near future. Planning for the exploration and use of unconventional water resources, such as gray water and sullage reuse, will greatly help to balance water shortage. In this research, sewage of swimming pools has been investigated because it is a type of urban sewage that has high technical, economic and environmental potential for implementation of urban sullage recycling project. A case study was carried out on 10 public swimming pools in Tehran to determine the volume and 7 pools for qualitative investigation on sewage of different parts of swimming pools. The results indicate that pools have a high quality and high volume wastewater that cause conceivable potential for recycling. For example, the average COD of the tested samples was 153 ppm and the maximum was 246 ppm, which is equivalent to organic load of weak urban wastewater. This wastewater also meets the standards of landscape irrigation in most of parameters, and in the other parameters such as organic load of some samples has a small variance from these standards, which could be met with a simple treatment unit like a depth filtration and an activated carbon. In addition, an average of 120 cubic meters of sullage per day is generated in each aquatic center complex, which is more than the production of gray water in a 700 people capacity residential complex. Reuse of this sullage, in addition to reducing transportation costs and load of centralized treatment plants, will reduce the pressure on water resources of our country by supplying water for non-potable purposes such as irrigation of landscaping.<strong>در سالهای اخیر استفاده بیرویه از منابع آب سطحی و زیرزمینی، تنش زیادی بر منابع آب ایران وارد کرده است. بررسی روند مصرف آب در سالهای گذشته و پیشبینیهای صورت گرفته از نیاز آبی در سالهای آتی، چشمانداز نامطلوبی از عدم تناسب بین تقاضا و منابع آب کشور در آینده نزدیک ترسیم میکند. برنامهریزی برای شناسایی و استفاده از منابع آبی نامتعارف، مانند استفاده مجدد از آب خاکستری و پساب، کمک شایانی به تعدیل کمبود آب خواهد نمود. در این پژوهش، فاضلاب تولیدی استخرهای شنا بهعنوان یکی از انواع فاضلاب شهری که از نظر فنی، اقتصادی و محیطزیستی از پتانسیل زیادی برای اجرای طرح استفاده مجدد پساب شهری برخوردار است، مورد بررسی قرار گرفت. مطالعه موردی بر روی 10 استخر شنای عمومی در شهر تهران برای تعیین حجم و 7 استخر برای بررسی کیفی فاضلاب تولیدی در بخشهای مختلف استخرهای شنا انجام شد. نتایج حاصل بیانگر آن است که آب دورریز در استخرها، فاضلابی با کیفیت و حجم زیاد است که پتانسیل خوبی برای استفاده مجدد دارد. بهعنوان مثال میانگین </strong><strong>COD</strong><strong> نمونههای آزمایش شده </strong><strong>ppm</strong><strong> 153 و بیشترین مقدار آن </strong><strong>ppm</strong><strong> 246 بود که معادل بار آلی فاضلاب ضعیف شهری است. این پساب در بسیاری پارامترها منطبق بر استانداردهای آبیاری فضای سبز است و در برخی موارد مانند بار آلودگی آلی تعدادی از نمونهها نیز اختلاف کمی با استانداردهای آبیاری فضای سبز دارد که با بهکارگیری یک تصفیه ساده همچون فیلتراسیون عمقی و کربن فعال، این استانداردها را اقناع خواهد نمود. افزون بر این، بهطور میانگین در هر مجموعه آبی روزانه 120 مترمکعب پساب تولید میشود که این عدد بیش از آب خاکستری تولیدی در یک مجتمع مسکونی 700 نفری است. استفاده مجدد از این پساب علاوه بر کاهش هزینههای انتقال و کاهش بار وارد بر تصفیهخانههای متمرکز، با تأمین آب مورد نیاز برای مصارف غیر شرب شهری مانند آبیاری فضای سبز منجر به کاهش فشار بر منابع آب کشور خواهد شد.</strong>https://www.wwjournal.ir/article_95931_cba1906865b1d7a60c7c8cab77e40fff.pdfمهندسین مشاور طرح و تحقیقات آب و فاضلاب اصفهانمجله آب و فاضلاب1024-593631120200320Locating Large Water Pipelines Using Arc-GIS Softwareمکانیابی خطوط بزرگ انتقال آب با استفاده از نرمافزار Arc-GIS1111178363110.22093/wwj.2018.100955.2506FAمحمد عطاریدانشجوی دکترای آب و سازههای هیدرولیکی، گروه عمران، دانشکده مهندسی، دانشگاه فردوسی مشهد، ایرانعباس خاشعی سیوکیدانشیار، گروه مهندسی آب، دانشکده کشاورزی، دانشگاه بیرجند، بیرجند، ایرانسعید اصغرزاده منظریکارشناس ارشد پدافند غیرعامل، گروه مدیریت بحران، دانشکده آمایش و پدافند غیرعامل، دانشگاه صنعتی مالک اشتر تهران، ایرانمعصومه مجردکارشناس ارشد مهندسی آب، گروه کشاورزی، دانشگاه ارومیه، ایرانJournal Article20171112Water Pipe Line are the lines that take water from different resources and transfer it to drinking needed nodes, industry or agriculture. Because of the intense shortage of water resources especially in the eastern and central reigns of our country, in the recent years some plans have been proposed for water transferring among basins. These projects not only have led to a lot of social conflict in the area that these project have been done but also causes some subversive acts along the pipe lines and dependent installation. So finding suitable location for pipe lines from the passive defense point of view will be very important. In this research a method for finding suitable location for great pipe lines according to different criteria such as privacy, access, military, economic, population, geology, geomorphology, climate and hydrology is introduced. Each criteria is classified to several subgroups. So all the subgroups are done quantification in software of Arc-GIS9.3. Then with super position of above layers, the planed area and high risk places are coloured and determinedon the map. The results shows that the route which has the best access and the least intersection with Faults, agricultural areas, rivers and gas pipe lines with 374 kilometers lengths are selected as the best options.<strong>خطوط بزرگ انتقال آب، خطوط لولهای هستند که آب را از چاه، منابع سطحی نظیر رودخانهها و یا از محل سدها برداشته و به گرههای نیاز شرب، صنعت یا کشاورزی منتقل میکنند. بهدلیل کمبود شدید منابع آب بهویژه در بخشهای شرقی و مرکزی کشور، طی سالهای اخیر طرحهایی برای انتقال آب بین حوضهای مطرح شده است. این امر سبب ایجاد تنشهای اجتماعی زیادی در مناطق اجرای طرح شده و همچنین باعث بروز اعمال خرابکارانه در مسیر خط انتقال و تأسیسات وابسته شده است. در نتیجه، مکانیابی خط انتقال از منظر پدافند غیرعامل از اهمیت بسیار بالایی برخوردار است. در این پژوهش به معرفی روش مکانیابی خطوط بزرگ انتقال با در نظر گرفتن شاخصهای حریم، دسترسی، نظامی، اقتصادی، جمعیتی، زمینشناسی و ژئومورفولوژی و اقلیم و هیدرولوژی پرداخته شد. هر کدام از شاخصها به چندین زیرشاخص طبقهبندی شد. بر این اساس کلیه زیرشاخصها در نرمافزار </strong><strong>Arc-GIS</strong><strong> کمّیسازی شدند. سپس با برهم نهی لایههای فوق، منطقه طرح لکهگذاری شده و نقاط با خطر بالا مشخص شدند. در نهایت با ترسیم نقشه پهنهبندی، منطقه امن برای مسیر خط انتقال از بین خطوط پیشنهادی مشخص شد.</strong>https://www.wwjournal.ir/article_83631_244e6d273d54f7adfd25decc3aa9a85c.pdf